MerLube Div., J.J. Merlin Systems, Inc.

MSDS Sheet for MerLube 918

Lubricants 317 | 422 | 517 | 829 | 918 | 962 | 1110 

 

MSDS Sheets -  317 | 422 | 517 | 829 | 918 | 962 | 1110 

 

Equipment | Online Sales | Online Distribution | Helpful Info | Back to JJ Merlin Homepage

MATERIAL SAFETY DATA SHEET (MSDS)

 Health: 0 ∑ Fire: 1 ∑ Reactivity: 0

SECTION 1- MATERIAL IDENTIFICATION

Material / Trade Name: Mer*Lube 918 Emergency Telephone: 330-666-8609

SECTION 2- INGREDIENT

Specific information is considered as a trade secret and is withheld per CEF 1910:1200 (h). Medical personnel requiring this information should contact J.J. Merlin Systems with their request per CER 1010:1200 (h).

SECTION 3- PHYSICAL DATA

Boiling Point: 409.0 F @ 15 mmHg Physical Form: homogeneous solution

Specific Gravity: .848 @ 77.0 F Solubility in H2 O, % by Volume: Insoluble

Vapor Pressure: n/a Evaporation Rate: > 1.0

Vapor Density: n/a Percent Volatiles: no data

Color and Odor: clear, L color 5Y O.5R Max pH: 6-7

Liquid Density: 7.060 lbs./gal @ 77.0 F

SECTION 4- FIRE AND EXPLOSION DATA

Flash Point (Method Used): 200o F PMCC

Flammability Limits: n/a

Extinguishing Media: Dry Chemical, foam, water spray (fog).

Unusual Fire Explosion Hazards: None

SECTION 5- REACTIVITY DATA

Stability Hazardous Polymerization

__X__ Stable ____ Unstable ____ May Occur __X__ Will Not Occur

Conditions and Materials to Avoid: Strong oxidizing agents.

Hazardous Decomposition Products: n/a

SECTION 6- OCCUPATIONAL EXPOSURE LIMITS

No exposure limits have been set for this product. As with all industrial materials, exposure of this product to the skin and eyes should be avoided.

SECTION 7- HEALTH INFORMATION

Eye irritation: non-irritating.

Skin irritation: FHSA Rating: not a primary skin irritant; Index 1.3

Oral toxicity: (FHSA & OSHA Rating) non-toxic

LD50 (8%-20% solutions); >10gm/kg

This product (or components, if a mixture) is not listed in IRAC Monographs, the NPT Sixth Annual report or the ACGIH TLVís as a carcinogen or potential carcinogen. It is not regulated by OSHA as a carcinogen.

SECTION 8- EMERGENCY AND FIRST AID PROCEDURES

Eyes: Flush with large amounts of water, lifting upper and lower lids occasionally.

Skin: Wash exposed areas of the body with soap and water.

Inhalation: Remove from area of exposure, seek medical attention if symptoms persist.

Ingestion: Immediately drink two large glasses of water; call a physician.

SECTION 9- EMPLOYEE PROTECTION

Respiratory Protection: Not required under normal conditions of use.

Protective Clothing: Safety glasses, goggles or face shield recommended to protect eyes from mists or splashing. Neoprene or rubber gloves recommended to prevent skin contact.

Other protective Measures: Employees must practice good personal hygiene, washing exposed areas of the skin and laundering contaminated clothing.

SECTION 10- ENVIRONMENTAL PROTECTION

 

Spill Clean-Up Procedures: Remove sources of ignition, contain spill to smallest area possible. Stop leak if possible. Pick up small spills with absorbent materials such as paper towels, "Oil Dry", sand or dirt. Recover large spills for salvage or disposal. Wash hard surfaces with safety solvent or detergent to remove remaining oil film. Follow local, state and federal disposal regulations.

SECTION 11- SPECIAL PRECAUTIONS

Store in closed containers below 120o F.

Keep away from oxidizing agents, excessive heat and ignition sources.

Store and use in well-ventilated areas.

Do not store or use near heat, sparks, or flame; store out of sun.

Do not puncture, drag or slide this container.

Drum is not a pressure vessel.

 

SECTION 12- TRANSPORTATION REQUIREMENTS

DOT Classification: Class 65 DOT Info.- 49 CFR 172.10: Not regulated by DOT

NOS Component: none RQ (Reportable Quantity)- 49 CFR 172.101: n/a

SECTION 13- REGULATORY INFORMATION

 

SARA 302 Components- 40 CFR 355 Appendix A: none California Proposition 65: none

SARA 313 Components- 40 CFR 372.65: none CERCLA RQ-40 CFR 302.4: none

SECTION 14- DATE

Date of Preparation: November 1, 1995

Date of Correction: December 2, 2007

Reason for change: Confirmation of updated information. Format presentation.

 

This information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any other process. Such information is to the best of the companyís knowledge and believed to be accurate and reliable as of the date indicated. However, no representation, warranty or guarantee of any kind, express or implied, is made as to its accuracy, reliability or completeness and we assume no responsibility for any loss, damage or expense, direct or consequential, arising out of use. It is the userís responsibility to satisfy himself as to the suitableness and completeness of such information for his own particular use.

mer*Lube 918 SAFETY DATA SHEET

liquids, lubricants, merlin, jjmerlin, merlin, lube, merlube 918, metal cutting, cutting tools, lubricant, safety data sheet