Lubricants

 New Products

 >BLADESAVER 24/7

 >QUICK-KUT

 >ALUMA-KUT 1776

 Original Merlube

 >General 422

 >Mid-Level 918

 >Premium 829

 Specialty Lubricants

 >317 Tapping

 >517 Solid

 >1110 Gel

 >Slick Stix

 

Merlube Homepage

 

Equip./Applicators

 

Merlube Video

 

Merlicator Manual

 

Online Sales

 

Online Distribution

 

Helpful Info

 

Corporate Profile

 

Policy Page

 

MSDS Sheets 

317  422  517  829  918  1110 Slick Stix

Bladesaver Quick-Kut

Aluma-Kut

 

Contact Us

 

 

MerLube Div., Adtec of Ohio

MSDS Sheet for MerLube Bladesaver 24/7

Link to MSDS Bladesaver 24/7

MATERIAL SAFETY DATA SHEET (MSDS)

                                           ∑ Health: 0 ∑ Fire: 1 ∑ Reactivity: 0 ∑

SECTION 1- MATERIAL IDENTIFICATION

Material / Trade Name: MerLube Bladesaver 24/7

Emergency Telephone:  330-666-8609

SECTION 2- INGREDIENT

Specific information is considered as a trade secret and is withheld per CEF 1910:1200 (h). Medical

personnel requiring this information should contact MerLube with their request per CFR 1010:1200 (h).

SECTION 3- PHYSICAL DATA

Boiling Point, 760 mm Hg: n/a Volatiles, % by Volume: n/a

Specific Gravity (H2 O=1): 0.92 Solubility in H2 O, % by Volume: Insoluble

Vapor Pressure, mm Hg: n/a Evaporation Rate, Butyl Acetate=1: n/a

Vapor Density, Air=1: n/a

Appearance and Odor: light amber liquid with faint fatty odor

SECTION 4- FIRE AND EXPLOSION DATA

Flash Point (Method Used): LEL: n/a UEL: n/a

315o C min. (Cleveland Open Cup)

Flammability Limits: n/a

Extinguishing Media: Dry Chemical, foam, halon. CO2, water spray (fog). Water stream may splash burning liquid and spread fire.

Special Fire Fighting Procedures: Combustible liquid. Use air supplied equipment for fighting interior fires. Cool fire exposed containers with water.

Unusual Fire Explosion Hazards: None

SECTION 5- REACTIVITY DATA

Stability Hazardous Polymerization

__X__ Stable ____ Unstable ____ May Occur __X__ Will Not Occur

Conditions and Materials to Avoid: Strong oxidizing agents.

Hazardous Decomposition Products: Combustion produces carbon monoxide and carbon dioxide along

with thick smoke.

SECTION 6- OCCUPATIONAL EXPOSURE LIMITS

No TLV has been set for this product. As with all industrial materials, exposure of this product to the skin and eyes should be avoided.

 

SECTION 7- HEALTH INFORMATION

Inhalation hazard is negligible unless heated to produce vapors or as a mist. Vapors or finely misted materials may irritate the mucous membranes and cause irritation, dizziness and nausea.

Eye contact may cause irritation. Irrigate eye with water for at least 15 to 20 minutes. Seek medical attention if symptoms persist.

Prolonged or repeated contact with skin may cause irritation of the hair follicles and block sebaceous glands, causing rash, acne or dermatitis.

Ingestion may irritate the digestive tract; seek medical attention if symptoms persist or if material is ingested in large quantities.

SECTION 8- EMERGENCY AND FIRST AID PROCEDURES

Eyes: Irrigate eyes with a heavy stream of water for at least 15 to 20 minutes.

Skin: Wash exposed areas of the body with soap and water.

Inhalation: Remove from area of exposure, seek medical attention if symptoms persist.

Ingestion: Call physician for advice.

SECTION 9- EMPLOYEE PROTECTION

Respiratory Protection: Respirators approved for organic vapors.

Protective Clothing: Safety glasses, goggles or face shield recommended to protect eyes from mists or splashing. Neoprene or rubber gloves recommended to prevent skin contact.

Other protective Measures: Employees must practice good personal hygiene, washing exposed areas of the skin several times daily and laundering contaminated clothing before re-use.

SECTION 10- ENVIRONMENTAL PROTECTION

 

Spill Clean-Up Procedures: Remove sources of ignition, contain spill to smallest area possible. Stop leak if possible. Pick up small spills with absorbent materials such as paper towels, "Oil Dry", sand or dirt. Recover large spills for salvage or disposal. Wash hard surfaces with safety solvent or detergent to remove remaining oil film. Follow local, state and federal disposal regulations.

Environmental Hazards: None

SECTION 11- SPECIAL PRECAUTIONS

Store in closed containers below 120o F.

Keep away from oxidizing agents, excessive heat and ignition sources.

Store and use in well-ventilated areas.

Do not store or use near heat, sparks, or flame; store out of sun.

Do not puncture, drag or slide this container.

Drum is not a pressure vessel.

SECTION 12- TRANSPORTATION REQUIREMENTS

Dot Shipping Name: Vegetable Oil DOT I.D. Number: 145100

DOT Classification: Class 65 UN Hazard Class: n/a

SECTION 13- DATE

Date of Preparation: June 1, 1995

Date of Correction: December 2, 2007

Reason for change: Confirmation of updated information.

This information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any other process. Such information is to the best of the companyís knowledge and believed to be accurate and reliable as of the date indicated. However, no representation, warranty or guarantee of any kind, express or implied, is made as to its accuracy, reliability or completeness and we assume no responsibility for any loss, damage or expense, direct or consequential, arising out of use. It is the userís responsibility to satisfy himself as to the suitableness and completeness of such information for his own particular use.

1245 S. Cleve-Mass Rd.; Ste 218 | Copley, Ohio 44306 | 330.666.8609  | sales@merlube.com

 

 

Mer*Lube is a division of JJ Merlin Systems which specializes in Lubricants and Lubricating Equipment. The Mer*Lube lubricants' are of the highest technology and are all environmentally safe. Our abrasive segments will allow you to fully utilize the capacity of your vertical spindle grinder. Our grinding wheel segments cut faster, generate less heat, hold form, produce heavy stock removal rates, and give desirable finishes.

 

Lubricants acculube trico solid paste

Merlube merlin systec segments grinding

Wheel abrasives stones machining industrial

 

Mer*Tap SAFETY DATA SHEET

liquids, lubricants, merlin, jjmerlin, merlin, mertap, metal cutting, cutting tools, lubricant, safety data sheet.